Pages

Wednesday, August 31, 2016

Hyperspectral Imaging Shines Light on a Mesoamerican Treasure

Scatterings image

Detail of a page of the Codex Selden, as revealed using hyperspectral imaging. [Image: Copyright © Journal of Archaeological Sciences: Reports, 2016, Elsevier; courtesy of Bodleian Libraries, University of Oxford, U.K.]

For more than 50 years, the Codex Selden, a rare Mesoamerican manuscript dating from around 1560, has frustrated scientific inquiry. Archaeologists have long known that the accordion-folded, 20-page leather codex likely contains a rich pictographic record of Mexico's culture and history, as seen by its indigenous Mixtec peoples during the upheavals of the earliest colonial period. But that original indigenous record has subsequently been completely covered by a layer of white gesso (gypsum and chalk). And recovering the original images without damaging the precious artifact itself has proved all but impossible.

Now, a research team from the Netherlands and the United Kingdom has used a thoroughly modern optical technique, hyperspectral imaging, to noninvasively burrow through the gesso and reveal the scenes beneath (J. Archeol. Sci.: Reports, doi: 10.1016/j.jasrep.2016.07.019). While much work remains to be done, the effort has already yielded some surprises.

A stubborn subject

Archaeologists first realized that the Codex Selden was a palimpsest—an original manuscript that has been subsequently covered—in the late 1950s, when several researchers attempted physically remove the gesso on one of the codex pages to reveal the writing beneath. The effort proved only marginally successful, however, and since then scientists have searched for ways to get at the original writing noninvasively.

The codex, however, has stubbornly resisted most techniques commonly used to investigate artworks of this kind. X-ray analysis, the most common technique, is useless in this case, because the organic paints used in the original pictographic writing don't absorb X-rays. Infrared imaging has revealed only limited information, as has another technique, photothermal tomography (which measures the thermal energy produced when colors absorb light).

Trying out hyperspectral imaging

Netherlands researchers Ludo Snijders of Leiden University and Tim Zaman of Delft University, along with David Howell of the Bodleian Library, University of Oxford, U.K., decided to take another crack at the Codex Selden. To do so, they zeroed in on hyperspectral imaging, which uses a combination of high-resolution, pixel-by-pixel spectroscopy and high-speed, intense data crunching to pull out detailed information on a given scene. Originally designed for military surveillance, the method has increasingly been applied in recent years in other spheres—from food safety to airport security—as costs, especially for data processing, have dropped (see "Hyperspectral Imaging for Safety and Security," OPN, October 2015).

The researchers began with one of the pages of the codex that had already been partly physically uncovered during the initial work in the 1950s. Scanning that page across the visible spectrum using a hyperspectral-imaging setup that had been recently acquired by the Bodleian Library, the team next applied principal component analysis and independent component analysis to reduce the huge volume of hyperspectral data into an interpretable image. Red pigments showed up particularly strongly; the hyperspectral technique was also able to tease out yellow pigments, which had previously been difficult to discern at all, as they tended to blend in with the gesso color.

Striking new view

The team was able to put the data from the hyperspectral imaging together with the previous information from optical photography, infrared photography and other techniques to form a striking new view of the original codex drawings (see image below). One of the researchers, archaeologist Ludo Snijders, noted in a press release that the text revealed by the new method "doesn't match that of other early Mixtec manuscripts. The genealogy we see appears to be unique.

Scatterings image

Pages of the Codex Selden on which the white gesso layer had been partly removed in a previous study (top) were hyperspectrally imaged. The hyperspectral data were combined with information from several other methods to reveal, noninvasively, the original pictographic scenes hidden under the gesso covering (bottom). [Image: Copyright © Journal of Archaeological Sciences: Reports, 2016, Elsevier; courtesy of Bodleian Libraries, University of Oxford, U.K.] [Enlarge image]

The researchers are using the hyperspectral results from the previously partly uncovered page as a sort of "style guide" for interpreting results from the rest of the document, where the gesso covering is more complete and the challenges of uncovering the palimpsest more formidable. Revealing the full text will likely be a long and difficult process, even with the hyperspectral addition to the toolkit.

Nonetheless, the results have been sufficient to excite the research community on the codex's potential to illuminate Mixtec history. And coauthor David Howell of the Bodleian Library is bullish on hyperspectral for other applications as well. "This is very much a new technique," he says, "and we've learned valuable lessons about how to use hyperspectral imaging in the future both for this very fragile manuscript and for countless others like it."


Source: Hyperspectral Imaging Shines Light on a Mesoamerican Treasure

Tuesday, August 30, 2016

Roma Rosa: A Surreal Infrared View of Rome

During a two-day trip to the magnificent city that is Rome, photographer Milán Rácmolnár came up with the brilliant idea of photographing Rome in infrared. The result is a different and pink perspective on the cityscapes.

If you are familiar with The Infra Series by conceptual documentary photographer, Richard Mosse, you will know that the man was known for the use of Kodak Aerochrome, a now discontinued reconnaissance infrared film, in rendering some captivating images of the ongoing war in Eastern Congo.

Milán Rácmolnár is no Richard Mosse, but he certainly accomplished a rare feat in shining a new light on a city that has been photographed countless times over the years. It was during a short visit to Rome, that the photographer decided he would seek sights and visuals that are not visible to the naked eye. 

"I like to concentrate on the human perception. For instance, the perception of the digital world or the perception of things that we can't sense visually, like sound waves."

municipality of rome infrared

city life in rome in infrared

Therefore, it seems logical that he chose infrared as a means to see what the naked eye cannot see. Nowadays, most people who want to create some dramatic infrared photos, will make use of infrared filters to achieve the desired results, or infrared film if they can find them. But Milán Rácmolnár found another way, an irreversible one!

Milán Rácmolnár explains that he decided to convert his Nikon D3200 to a full spectrum camera. The photographer disassembled his camera body to remove the IR filter and then reassembled everything. All cameras come with an internal IR filter, and the latter filters the biggest part of the visible light. So you can say you end up with a mostly monochrome picture. The photographer adds that some of the visible light will pass through the filter and will therefore affect the various alpha layers.

"Of course, as we cannot see this wavelength, it is always just pure fiction, but the colour of the infrared can only be interpreted as a ratio to the visible light. As I photographed in full spectrum, the infrared light becomes, if I may say so, an added colour to the existing colour palette. As a result, the white balance of the picture has to figure out into what colour range it belongs."

Busy streets of rome in infrared

There was always a reddish tone to the pictures but Milán Rácmolnár said he wanted to preserve it as he got used to this look while he was experimenting. According to him, most IR photographers usually post process their photos to look vivid by mixing some of the colour channels and adding contrast to them. He went to such lengths because he liked the look of how the infrared light mixes with the visible light. However, the process was not without its drawbacks.  

"With this method, all the pictures turned a little hazy because the lens does not refract the normal and the infrared light equally as far as I know. It is an effect similar to chromatic aberration," says Milán Rácmolnár.

Despite this, the result is "Roma Rosa" – a stunning project that depicts Rome in pink. Milán Rácmolnár shows some of the famous landmarks and sights of the city in pink and cyan hues. The colours obtained with the removal of the IR filter lend the landscapes a poetic and surreal feel. It almost looks like all the trees turned to cherry blossoms in the summer. Even the Colosseum appears different surrounded by pink cypress trees.

strerts of rome

And if you've ever wondered why trees and plants were the most affected in infrared photography, click here.

Have a look at the Roma Rosa series by Milán Rácmolnár on his website.

All images used with the permission of Milán Rácmolnár.


Source: Roma Rosa: A Surreal Infrared View of Rome

Monday, August 29, 2016

Infrared with the Kodak DCS 520 / Canon DC2000

John Seaman , Aug 28, 2016; 02:29 p.m.

Its not every day that you find a once mighty $15000 professional digital SLR in a charity shop window. The Kodak DCS520 is a Canon EOS 1n with a digital body added by Kodak. The same camera was sold as the Canon DC2000. The sensor is only 2MP, its big brother the DCS560 has a 6MP sensor, which would have been nice, but you can't expect miracles.

It came with the charger and three batteries, one of which proved to be viable. It takes two PCMIA cards into which you can plug a compact flash or microdrive. To my surprise it worked perfectly with a 4GB card. The only real problem with it is a bleed in the top LCD.

John Seaman , Aug 28, 2016; 02:31 p.m.

These were the first DSLR's with a preview screen, not huge but better than nothing. The rear command dial works by pressing select button to navigate the menus – it took me a while to discover this.

The camera records images in a proprietary RAW format. The files have a TIF subscript but they are not TIFFs, however I found that ACR opens them correctly and enables RAW manipulation. I increased the image size to 6MP on saving as JPEG, and did some sharpening. But 2MP is 2MP. JPEG's can also very slowly be generated in the camera, if it is set up to do so.

John Seaman , Aug 28, 2016; 02:35 p.m.

I immediately noticed that there is a filter, for antialiasing and infra red blocking, not directly in front of the sensor as with other cameras, but at the front of the mirror box, just behind the lens. And it is easily removed for cleaning. Or perhaps, infra red shooting. So I bought an infra red filter for my 28-80 USM, and tried it out.

In use it was impossible to see the image through the filter, so the procedure was: compose and focus. Adjust focus back to the infrared marker on the lens. Attach filter. Close eyepiece blind (actually this didn't make as much difference to the exposure as I expected) and press the shutter. I got shutter speeds around half a second at F/11 and 200ISO (the lowest available, it goes up to 1600).

John Seaman , Aug 28, 2016; 02:37 p.m.

Here are some results, after RAW conversion, levels adjustment, and conversion to monochrome. The shots were done around Kirby Muxloe Castle, near Leicester, on a very sunny morning. My first attempt at infrared, which I never saw the attraction in previously.

John Seaman , Aug 28, 2016; 02:40 p.m.

Oops forgot the picture. One good thing about the DCS is that being based on an older film camera, it works with some older Sigma lenses which aren't compatible with later DSLR's.

John Seaman , Aug 28, 2016; 02:42 p.m.

Another example. I hope the members of the EOS forum don't mind me cluttering it up with this stuff.

John Seaman , Aug 28, 2016; 02:45 p.m.

Finally, this is what the images look like straight from the camera. Any suggestions as to how best to process them would be welcome, and many thanks for looking.

By the way I forgot to mention that the DCS 520 was introduced in 1998.

John Seaman , Aug 29, 2016; 08:43 a.m.

JDM I had read your post but it didn't click that yours was the sister camera to mine. You should be able to use CF cards larger than 1GB by upgrading to the latest firmware - if you are into that kind of thing. You can still download the manual, software, firmware etc from Kodak - rather surprisingly I thought. But I expect you already know this.

(link)


Source: Infrared with the Kodak DCS 520 / Canon DC2000

Friday, August 26, 2016

Roma Rosa: A Surreal Infrared View of Rome

During a two-day trip to the magnificent city that is Rome, photographer Milán Rácmolnár came up with the brilliant idea of photographing Rome in infrared. The result is a different and pink perspective on the cityscapes.

If you are familiar with The Infra Series by conceptual documentary photographer, Richard Mosse, you will know that the man was known for the use of Kodak Aerochrome, a now discontinued reconnaissance infrared film, in rendering some captivating images of the ongoing war in Eastern Congo.

Milán Rácmolnár is no Richard Mosse, but he certainly accomplished a rare feat in shining a new light on a city that has been photographed countless times over the years. It was during a short visit to Rome, that the photographer decided he would seek sights and visuals that are not visible to the naked eye. 

"I like to concentrate on the human perception. For instance, the perception of the digital world or the perception of things that we can't sense visually, like sound waves."

municipality of rome infrared

city life in rome in infrared

Therefore, it seems logical that he chose infrared as a means to see what the naked eye cannot see. Nowadays, most people who want to create some dramatic infrared photos, will make use of infrared filters to achieve the desired results, or infrared film if they can find them. But Milán Rácmolnár found another way, an irreversible one!

Milán Rácmolnár explains that he decided to convert his Nikon D3200 to a full spectrum camera. The photographer disassembled his camera body to remove the IR filter and then reassembled everything. All cameras come with an internal IR filter, and the latter filters the biggest part of the visible light. So you can say you end up with a mostly monochrome picture. The photographer adds that some of the visible light will pass through the filter and will therefore affect the various alpha layers.

"Of course, as we cannot see this wavelength, it is always just pure fiction, but the colour of the infrared can only be interpreted as a ratio to the visible light. As I photographed in full spectrum, the infrared light becomes, if I may say so, an added colour to the existing colour palette. As a result, the white balance of the picture has to figure out into what colour range it belongs."

Busy streets of rome in infrared

There was always a reddish tone to the pictures but Milán Rácmolnár said he wanted to preserve it as he got used to this look while he was experimenting. According to him, most IR photographers usually post process their photos to look vivid by mixing some of the colour channels and adding contrast to them. He went to such lengths because he liked the look of how the infrared light mixes with the visible light. However, the process was not without its drawbacks.  

"With this method, all the pictures turned a little hazy because the lens does not refract the normal and the infrared light equally as far as I know. It is an effect similar to chromatic aberration," says Milán Rácmolnár.

Despite this, the result is "Roma Rosa" – a stunning project that depicts Rome in pink. Milán Rácmolnár shows some of the famous landmarks and sights of the city in pink and cyan hues. The colours obtained with the removal of the IR filter lend the landscapes a poetic and surreal feel. It almost looks like all the trees turned to cherry blossoms in the summer. Even the Colosseum appears different surrounded by pink cypress trees.

strerts of rome

And if you've ever wondered why trees and plants were the most affected in infrared photography, click here.

Have a look at the Roma Rosa series by Milán Rácmolnár on his website.

All images used with the permission of Milán Rácmolnár.


Source: Roma Rosa: A Surreal Infrared View of Rome

Wednesday, August 24, 2016

Wordy Wednesday #224 “Stormy Weather: Infrared”

While you may not think you an shoot in digital infrared on a stormy day, this shot shows the results when you do. I'm not a scientist but I guess the deciduous trees have stored enough chlorophyll to reflect on this shot made with a Canon EOS 50D converted to infrared-only capture by Life Pixel. Lens was a Tamron 18-200mm f/3.5-6.3 lens at 42mm. Exposure was 1/250 sec at f/10 and ISO 800.

story.IR

I opened the RAW file in Adobe Photoshop, then used the free Silver Efex Pro and used the default preset—I typically suppress "grain" by moving the slider all the way to the left—the image was already a little noisy because of underexposure—and then tweaking Contrast, Brightness and Structure. Next I applied the Glamour Glow filter from the free Color Efex Pro and finished it off with the Platinum toning option in PixelGenius indespensible PhotoKit 2 —it does lots more than toning.

In my experience, I've found that LifePixel does a great job with IR conversions. You can get $50 OFF with Priority Processing Upgrade by using coupon code:farace-ir50. Don't miss out on this soon to expire offer, order your conversion today!IR.book.cover

My book The Complete Guide to Digital Infrared Photography is currently out of print but you can get an affordable used copy or not-so-affordable new copies of the book from Amazon.com.

Related


Source: Wordy Wednesday #224 "Stormy Weather: Infrared"

Tuesday, August 23, 2016

Spectroscopy IR Detector Market Worth 224.5 Million USD by 2022

PUNE, India, August 23, 2016 /PRNewswire/ --

According to the MarketsandMarkets report "Spectroscopy IR Detector Market by Detector Technology (DTGS, MCT, InGaAs), Spectrum Sensitivity (NIR, Mid IR, and Far IR), Cooling Requirement (Cooled and Uncooled), Product Type (Benchtop, Portable, Hyphenated) - Global Forecast to 2022", published by MarketsandMarkets, the overall market is estimated to be worth USD 224.5 Million by 2022, growing at a CAGR of 6.9% between 2016 and 2022, whereas the unit shipment of IR detector is expected to grow at a CAGR of 7.7% between 2016 and 2022.

     (Logo: http://photos.prnewswire.com/prnh/20160303/792302 )

Browse 45 market data Tables and 69 Figures spread through 86 Pages and in-depth TOC on "Spectroscopy IR Detector Market".

http://www.marketsandmarkets.com/Market-Reports/spectroscopy-ir-detector-market-142905081.html

Early buyers will receive 10% customization on this report. 

The major factors driving the growth of the IR detector market for IR spectroscopy include upgradation of IR spectroscopy devices by replacing with new IR detector modules and the growing shipment of IR spectroscopy devices in various industries.

The benchtop IR spectroscopy device segment held the largest share of the IR detector market in 2015 

The benchtop IR spectroscopy device segment held the largest share of the IR detector market in 2015, while the market for portable IR spectroscopy device is expected to grow at a significant rate between 2016 and 2022. In the current scenario, benchtop IR spectroscopy plays a key role in a number of industries such as pharmaceutical, biological, chemicals, food & beverages, and others. The increasing shipment of benchtop and portable IR spectroscopy devices is driving the growth of the IR detector market.

Mid IR detector plays a key role in the IR detector market 

The IR detector market for IR spectroscopy has been segmented on the basis of spectrum sensitivity into NIR, Mid IR, and Far IR. Of all these, mid IR is expected to hold the largest market share during the forcast period owing to the wide range of applications of mid IR spectroscopy in the research and industrial sector. Along with this, the market for NIR spectroscopy devices is expected to grow at a significant rate during the forecast period, which would, in turn, drive the growth of NIR detector market in the near future.

APAC region would grow at a significant rate during the forecast period 

The market in APAC is expected to grow at a significant rate in the IR detector market for IR spectroscopy in the near future because of factors such as the presence of a large number of IR detector and IR spectroscopy device manufacturing companies in the region. For instance, in April 2016, Hamamatsu Photonics K.K. (Japan) announced its plans to establish a new optosemiconductor manufacturing unit in Japan by February 2017. Similarly, Thermo Fisher Scientific Inc. (U.S.) has expanded its business by establishing an innovation center in China; it has invested around USD 9.5 million for R&D in this center. Also, DANI Instruments SpA (Italy) has signed a distribution agreement with Labindia Instruments Pvt. Ltd. (India).

Inquiry Before Buying: http://www.marketsandmarkets.com/Enquiry_Before_Buying.asp?id=142905081

The key companies operating in the IR detector market include Hamamatsu Photonics K.K. (Japan), Excelitas Technologies Corp. (U.S.), LASER Components GmbH (Germany), UTC Aerospace Systems (U.S.), Newport Corporation (U.S.), and others.

Browse Related Reports 

Infrared Detector Market by Type (MCT, INGAAS, Pyroelectric, Thermopile Microbolometer and Others), Technology (Cooled Infrared, and Uncooled Infrared), Wavelength (Short, Medium, and Long Infrared), Application, and Geography - Global Forecast to 2020

http://www.marketsandmarkets.com/Market-Reports/ir-detector-market-161116561.html

IR Spectroscopy Market by Spectrum Sensitivity (NIR, Mid IR, and Far IR), Product Type (Benchtop, Micro, Portable, and Hyphenated), Vertical (Biological, Pharmaceuticals, Chemicals, Food & Beverages, Environmental), and Geography - Global Forecast to 2022

http://www.marketsandmarkets.com/Market-Reports/ir-spectroscopy-market-42486905.html

About MarketsandMarkets 

Read More

MarketsandMarkets is the largest market research firm worldwide in terms of annually published premium market research reports. Serving 1700 global fortune enterprises with more than 1200 premium studies in a year, M&M is catering to a multitude of clients across 8 different industrial verticals. We specialize in consulting assignments and business research across high growth markets, cutting edge technologies and newer applications. Our 850 fulltime analyst and SMEs at MarketsandMarkets are tracking global high growth markets following the "Growth Engagement Model - GEM". The GEM aims at proactive collaboration with the clients to identify new opportunities, identify most important customers, write "Attack, avoid and defend" strategies, identify sources of incremental revenues for both the company and its competitors.

M&M's flagship competitive intelligence and market research platform, "RT" connects over 200,000 markets and entire value chains for deeper understanding of the unmet insights along with market sizing and forecasts of niche markets. The new included chapters on Methodology and Benchmarking presented with high quality analytical infographics in our reports gives complete visibility of how the numbers have been arrived and defend the accuracy of the numbers.

We at MarketsandMarkets are inspired to help our clients grow by providing apt business insight with our huge market intelligence repository.

Contact:Mr. RohanMarkets and MarketsUNIT no 802, Tower no. 7, SEZMagarpatta city, HadapsarPune, Maharashtra 411013, IndiaTel: +1-888-600-6441Email: sales@marketsandmarkets.com

Visit MarketsandMarkets Blog@ http://www.marketsandmarketsblog.com/market-reports/electronics-and-semiconductorsConnect with us on LinkedIn @ http://www.linkedin.com/company/marketsandmarkets


Source: Spectroscopy IR Detector Market Worth 224.5 Million USD by 2022

Sunday, August 21, 2016

AlphaMirrorless 021: Making Infrared Images

AlphaMirrorless 021: Making Infrared Images

We are always looking to make unique and interesting images, and Infrared photography gives us a totally different and unique look to the world around us. The technology can be a little difficult to understand, in this episode of the AlphaMirrorless podcast, Juan and Andy explain what Infrared photography is, where to get a camera converted to IR, and how to go about making images.

We don't always have all the answers, but if we don't we will research it and try to give you the best answer we can. So what have you got to lose, go ahead and send in your questions to us by going to this form.

Links mentioned on the episode Wishes of the Week
  • Juan: Lots of puffy clouds in your sky
  • Andy: I wish that the 70-300 Sony G lens I just bought is AWESOME
  • Picks of the Week Connect with Our Hosts & Guests
    Source: AlphaMirrorless 021: Making Infrared Images

    Saturday, August 20, 2016

    Mono magic: Black and white landscape photography

    Black & white photography enables a more personal interpretation of the landscape. Lee Acaster, winner of multiple photo awards, explains

    With no colour to rely on, use texture, tone and lines to draw the reader in and give a 3D feel

    With no colour to rely on, use texture, tone and lines to draw the reader in and give a 3D feel

    We all see the world around us in colour, but as photographers we have the opportunity to look beyond this and view it as form, tone and texture. Shooting in black & white opens up a whole new landscape hidden beneath the surface.

    Colour landscape photography relies very heavily on light and weather conditions, and we are almost bound by the scene that nature presents to us. However, black & white photography offers the opportunity to create a more personal interpretation.

    New mindset

    There is much more to creating a successful monochrome image than simply looking back through the hard drive to salvage a shot by converting it to greyscale (although this can bring about desirable results, particularly with scenes that were too contrasty to be successful in colour). To make the most of shooting in black & white, you'll need to develop a whole new mindset before you even press the shutter. Whereas colour photography is dependent on the relationship between the various hues in a scene, when this is taken out of the equation other factors take on much greater prominence.

    The tonal values in the image become more important, and although it's not always easy to visualise these, with a little practice you can become much more adept at picturing the landscape as areas of light and shadow.

    Shooting digitally gives us an added advantage in this regard. By switching your camera's picture style to monochrome, you get an instant preview of how the image could look in black & white, although it is worth noting that a raw file will also retain the colour information and give you much greater control in post-production.

    Turning on the monochrome picture style helps you to see the world in black & white, and highlight subjects

    Turning on the monochrome picture style helps you to see the world in black & white, and highlight subjects

    This monochrome preview shouldn't be seen as the final image, though, as one of the most liberating aspects of black & white photography is that you have the ability to alter the tonal range of individual colours later, as well as having much more control over the highlights and shadows. This allows you to recreate the image you are visualising out in the field and exercise a degree of creative influence over it.

    Shape and form

    To create striking landscape images, it pays to look for strong lines and simple compositions. Larger areas of fine detail can easily lose prominence in the overall image in black & white, so it becomes much more about the shapes in the landscape. Looking at the scene as a whole can help you to create a stunning and effective composition, and building your image around one or two key focal points will help with this. Texture also plays an important role; with no colour to focus on, it adds depth and substance to a scene. As with colour, it can be particularly useful to have interesting foreground detail when shooting wideangle landscapes, but with black & white, contrast is the important element to consider, be it in ripples of sand with deep shadows, or backlit leaves or grasses.

    Bored of boulders? The old tyres add foreground interest and suit the topic

    Bored of boulders? The old tyres add foreground interest and suit the topic

    Creating a route through the image is a great technique to engage the viewer, and black & white is the perfect medium for doing this. Light and shadow can become key compositional elements. The eye is naturally drawn to the contrast when very dark and very light areas meet in a black & white image, so use these to create focal points and lead-in lines. A shadow falling across a field or hill, or a patch of sunlight on the sea, can be just as important an element within a shot as physical objects such as a fence or building.

    Processing

    By using light and shade in this way, the viewer is given a 'starting point'. Typically, this is introduced around the edges of the frame, and then the eye is led into the key focal points of the image. You can enhance this effect even further in processing, which, whether in the darkroom or digitally, has always played an important role in creating great mono images. Gradient and Radial filters provide a simple and effective method of concentrating the viewer's attention on the important parts of the image.

     Careful vignetting can focus attention on the subject and make the most of tones

    Careful vignetting can focus attention on the subject and make the most of tones

    Creating a vignette effect by darkening the edges of the frame, and increasing the contrast around the key components of the shot, will naturally lead the viewer's eye towards these lighter areas and make it linger there. The same approach can be applied in reverse to a high-key image, where the darker areas become the focal point.

    It's this ability to control the overall tonal range of the image that makes digital black & white photography so rewarding. This process and technique is so much more than just simply converting an image to greyscale.

    Use the natural interplay of light and dark as a key compositional tool

    Use the natural interplay of light and dark as a key compositional tool

    Kit list Canon EOS 5D Mark II

    EOS-5D-Mark-II-side-24mm

    I had my Canon EOS 5D Mark II converted to infrared (using a 720nm filter) purely for mono work. I love the extra contrast and slightly surreal effects I can achieve with it.

    Sony Alpha 7R

    Pic_2_Sony

    I've recently replaced my main kit with a Sony Alpha 7R mirrorless system. It's lightweight, and the dynamic range and resolution are superb.

    Zeiss Distagon T* 18mm f/3.5

    Pic_4_Sonnar-55mm-f1.8

    I use a Zeiss Distagon T* 18mm f/3.5 lens more than any other. It's robust and beautifully built, and performs well in colour and on my infrared body.

    Sonnar T* FE 55mm f/1.8 ZA

    Pic_3_Distagon-18mm-T

    Lately I've found myself increasingly using a 55mm lens, and the Sonnar T* FE 55mm f/1.8 ZA is light, fast and pin-sharp.

    Manfrotto head

    Pic_6_Manfrotto_head

    I like a very stable tripod, and they don't come much sturdier than a Gitzo. A geared head is a must for me; my favourite is the Manfrotto XPRO Geared 3 Way Head.

    Lee Filters system

    Pic_5_LEE_polariser

    I still use filters for my black & white photography, in particular a Lee Filters circular polariser, which is useful for adding contrast to skies.

    Alternative technique infrared  Haze is reduced and blue skies look particularly dramatic when shooting infrared

    Haze is reduced and blue skies look particularly dramatic when shooting infrared

    Shooting in infrared opens up a whole new dimension to black & white landscape photography. When using an infrared filter or IR-converted camera, most of the visible light is blocked, allowing only the infrared spectrum to reach the sensor. In practice, this can transform images and add a surreal, dreamlike quality to them.

    Foliage becomes lighter, blue skies become much darker and atmospheric haze is reduced. This is often used to create the ghostly looking infrared shots most of us are familiar with, but it can also be used in a much subtler way to enhance contrast and alter the expected dynamics of light and shade within an image.

    Make the most of infrared's 'bleaching' effects on leaves and undergrowth

    Make the most of infrared's 'bleaching' effects on leaves and undergrowth

    On a budget

    Hoya_R72

    Converting a camera to infrared can be quite costly, and as it's usually irreversible, it requires a second camera body. The advantages of a converted body are that you can preview the effect in live view, and the camera will operate at its usual shutter speeds. A much cheaper alternative is to use a screw-in filter such as a Hoya R72 Infrared.

    Unfortunately, you will need to compose your picture before attaching the almost opaque filter to the lens, and shutter speeds are significantly increased to one or two minutes. This can prove problematic when shooting subjects that are prone to movement, such as foliage, but it's also a good way to experiment with the technique.

    5 steps to processing in B&W

    Processing your black & white images well is vital to creating an impressive final image; it is also where you really get to add your creative input. Simply removing the colour and converting the image to greyscale will often lead to disappointing results, and can leave you with a rather flat and lifeless photograph.

    Increasing the tonal range by adjusting contrast, highlights and shadows will add more punch to your images, and the use of dodging and burning alters the dynamics of a shot. A quick and easy way to do this in Lightroom is by adopting Graduated and Radial filters, which you can use to concentrate attention onto the parts of the image that are most important to your composition. The soft-feathered edges of these filters allow you to increase contrast, sharpness, light and shadow within specific areas in a subtle manner.

    1. Original raw file

    Screen Shot 2016-08-17 at 14.56.12

    When shooting in raw, even if your camera was set to monochrome the file includes all colour information. Although the source file might look quite lifeless, this gives you better control over your final image and the ability to adjust tones more accurately.

    2. Convert to B&W

    Screen Shot 2016-08-17 at 14.56.51

    The first step is to switch the image to black & white in the Develop sidebar. Adjusting the Contrast, Highlights, Shadows and Clarity will start to lift the image, giving you a wider tonal range. You can also alter the tone of individual colours using the Black and White Mix sliders.

    3. Graduated filters

    Screen Shot 2016-08-17 at 14.57.04

    With the Graduated tool, start darkening or lightening specific areas of the image. Using several of these and coming in from different directions enables you to create a vignette effect, to draw the viewer's eye to the important areas of the image. Hence, you can adjust the exposure and contrast.

    4. Adding Radial filters

    Screen Shot 2016-08-17 at 14.57.23

    Whereas Graduated filters give you a sweeping effect, Radial filters are perfect for making adjustments to specific areas. They can be used to accentuate highlights and shadows, detail and textures, and are a good way to add depth and interest to the important areas of the photograph.

    5. Final image

    Screen Shot 2016-08-17 at 14.57.31

    After some final tonal adjustments and finishing touches, such as sharpening, you can create stimulating and original images that will enable you to see the landscape in a whole new light. It's well worth printing your best work – the tones and textures of mono can look wonderful in a nice frame.

    About Lee Acaster

    Unknown

    Based in East Anglia, Lee is an amateur photographer who has a love of landscapes. He is widely published and has won numerous national awards, including AP's Amateur Photographer of the Year 2015 competition.

    Website: www.leeacaster.com


    Source: Mono magic: Black and white landscape photography

    Friday, August 19, 2016

    First State Focus: Photographing a hidden world

    A walnut tree in Austin, Texas near the Texas State Capitol Building on August 5, 2010. Joe del Tufo made the image on a road trip in marks is as one of his favorite infrared photos.(Photo: Courtesy of Joe del Tufo)

    Don't adjust your screen, these photos look just as they're intended. Joe del Tufo's infrared photography displays a whole world invisible to the human eye.

    By modifying a digital camera with a filter that blocks out the visible light spectrum, del Tufo is able to capture just near-infrared and infrared wavelengths of light.

    Infrared light exists just below the visible light range on the light spectrum.

    "When I was first getting into it I would often be surprised by what I got versus what I was expecting," del Tufo said. "There was a forest fire in California and in some cases the fire went up a tree like a candy cane. When you looked at it in person, it just looked like a burned up tree. When you looked at it in infrared you could see the living parts of the tree very distinctly."

    The Jet Star roller coaster in Seaside Heights, N.J. was destroyed by Hurricane Sandy in 2012 when the storm plunged the ride into the ocean. Before the coaster was demolished, del Tufo travelled to the Jersey Shore to make an image of the semi-submerged ride but was chased off by police officers keeping the area clear. Af ter befriending a construction worker del Tufo was able to make an infrared image of the attraction. (Photo: Courtesy of Joe del Tufo)

    Infrared photography dates back to the early 1900's when photos were primarily black and white. As digital cameras have progressed over the last ten years, the technique has taken on a new life in color.

    "It's well over 100 years old now but it's still a valid art form," del Tufo said.

    Infrared images have a stark magenta hue in digital color cameras when they're first taken, but by taking the image into a program like Photoshop and converting the red channels in the image to blue, and likewise the blue to red, the image takes on a more familiar look with deep blue skies.

    The technique also requires a photographer to break the traditional rules of photography. Typically photographers avoid harsh light in midday for the "golden hour" of early morning or dusk.

    An engine from the Wilmington & Western Railroad moves down the tracks in this photograph from 2011.  (Photo: Courtesy of Joe del Tufo)

    "You want to be perpendicular to the light, so shooting at high noon is ideal," del Tufo said.

    For the past 10 years del Tufo has a variety of modified cameras to make his infrared photos. His latest is a Nikon D7100 modified by Kolari. At 24 megapixels, the body has a limited focal length range at which del Tufo can shoot, giving him only about 60mm of latitude to keep an image in focus.

    On Saturday del Tufo will work with 4Youth Productions, a group that works with under privileged students and teaches them different photographic techniques.

    On a month-long road trip devoted to infrared photography del Tufo and his family crossed the country looking for thoroughly documented landmarks they could show in a different light. On August 10, 2010 del Tufo finally made an image he was happy with of the St. Louis arch. "It took a long time to find the right frame ," del Tufo said. "Once I found it the previous hundred shots meant nothing." (Photo: Courtesy of Joe del Tufo)

    "It gets them out of the city looking at different things and seeing it with a different eye," del Tufo said. "Seeing what some birds and snakes can see and use to get their food. We can use it to realize there is more than what our eye is able to see."

    But del Tufo doesn't do all the teaching when he's out with the young students.

    "What I've noticed about them is this is a very new experience, and they see things I would never think of seeing," del Tufo said. "I learn from them sometimes."

    Read or Share this story: http://delonline.us/2b9qL0u


    Source: First State Focus: Photographing a hidden world

    Thursday, August 18, 2016

    IR Spectroscopy Market Worth 1.26 Billion USD by 2022

    PUNE, India, August 18, 2016 /PRNewswire/ --

    According to new market research report "IR Spectroscopy Market by Spectrum Sensitivity (NIR, Mid IR, and Far IR), Product Type (Benchtop, Micro, Portable, and Hyphenated), Vertical (Biological, Pharmaceuticals, Chemicals, Food & Beverages, Environmental), and Geography - Global Forecast to 2022", published by MarketsandMarkets, the overall market is expected to be valued at USD 1.26 Billion by 2022, growing at a CAGR of 6.5% between 2016 and 2022.

         (Logo: http://photos.prnewswire.com/prnh/20160303/792302 )

    Browse 38 market data Tables and 75 Figures spread through 135 Pages and in-depth TOC on "IR Spectroscopy Market"

    http://www.marketsandmarkets.com/Market-Reports/ir-spectroscopy-market-42486905.htmlEarly buyers will receive 10% customization on this report.

    The major factors driving the growth of the IR spectroscopy market include regulatory framework for process analytical technology in the pharmaceuticals industry, increase in R&D investment in life science, and continuous technological advancements in IR spectroscopy.

    The pharmaceuticals sector to hold the largest market share during the forecast period 

    The pharmaceuticals sector held the largest share of the IR spectroscopy market in 2015, while the market for the biological and chemicals sectors is expected to grow at a significant rate between 2016 and 2022. In the current scenario, IR spectroscopy plays a key role in the pharmaceutical excipient manufacturing process. Growing acceptance of new international cGMP & cGDP certification is expected to increase the usage of IR spectroscopy instruments, thereby driving the growth of the market.

    MID IR spectroscopy plays a key role in the IR spectroscopy market 

    The IR Spectroscopy Market has been segmented on the basis of spectrum sensitivity into NIR, Mid IR, and Far IR; of all these, Mid IR is expected to hold the largest market share during the forcast period, owing to the wide range of applications of Mid IR spectroscopy for the research and industrial sector. Along with this, the market for NIR spectroscopy devices is expected to grow at a significant growth rate during the forecast period.

    North America expected to hold the largest market share in the near future 

    North America is expected to hold the largest market share and dominate the IR spectroscopy market in the near future because of the factors such as stringent drug development regulations and increase in government funding for R&D in North America. The market growth can also be attributed to the rise in proteomics research and various conferences that provide a platform for key players to showcase new products and technologies.

    Inquiry Before Buying: http://www.marketsandmarkets.com/Enquiry_Before_Buying.asp?id=42486905

    The key players in the market include General Electric Company (U.S.), Olympus Corporation (Japan), Ashtead Technology Ltd. (U.K.), Mistras Group Inc. (U.S.), Eddyfi NDT Inc. (Canada), Ether NDE Limited (U.K.), Zetec Inc. (U.S.), TUV Rheinland AG (Germany), Ibg NDT System Corporation (U.S.), Fidgeon Limited (U.K.), Magnetic Analysis Corporation Inc. (USA) among others.

    Browse Related Reports 

    Infrared Imaging Market by Component (IR Lens System, IR Sensor, IR Detector), Technology (Cooled, Uncooled), Type (Fixed, Portable), Wavelength (NIR, SWIR, LWIR, FIR), Application, & Geography - Analysis and Forecast to 2022http://www.marketsandmarkets.com/Market-Reports/infrared-IR-sensing-imaging-market-593.html

    Infrared Detector Market by Type (MCT, INGAAS, Pyroelectric, Thermopile Microbolometer and Others), Technology (Cooled Infrared, and Uncooled Infrared), Wavelength (Short, Medium, and Long Infrared), Application, and Geography - Global Forecast to 2020http://www.marketsandmarkets.com/Market-Reports/ir-detector-market-161116561.html

    Know More About our Knowledge Store @ http://www.marketsandmarkets.com/Knowledgestore.asp

    About MarketsandMarkets 

    MarketsandMarkets is the largest market research firm worldwide in terms of annually published premium market research reports. Serving 1700 global fortune enterprises with more than 1200 premium studies in a year, M&M is catering to a multitude of clients across 8 different industrial verticals. We specialize in consulting assignments and business research across high growth markets, cutting edge technologies and newer applications. Our 850 fulltime analyst and SMEs at MarketsandMarkets are tracking global high growth markets following the "Growth Engagement Model - GEM". The GEM aims at proactive collaboration with the clients to identify new opportunities, identify most important customers, write "Attack, avoid and defend" strategies, identify sources of incremental revenues for both the company and its competitors.

    M&M's flagship competitive intelligence and market research platform, "RT" connects over 200,000 markets and entire value chains for deeper understanding of the unmet insights along with market sizing and forecasts of niche markets. The new included chapters on Methodology and Benchmarking presented with high quality analytical info graphics in our reports gives complete visibility of how the numbers have been arrived and defend the accuracy of the numbers.

    We at MarketsandMarkets are inspired to help our clients grow by providing apt business insight with our huge market intelligence repository.

    Contact:Mr. RohanMarkets and MarketsUNIT no 802, Tower no. 7, SEZMagarpatta City, HadapsarPune, Maharashtra 411013, IndiaTel: + 1-888-600-6441Email: sales@marketsandmarkets.com

    Visit MarketsandMarkets Blog@ http://www.marketsandmarketsblog.com/market-reports/electronics-and-semiconductorsLinkedIn @ http://www.linkedin.com/company/marketsandmarkets

    SOURCE MarketsandMarkets


    Source: IR Spectroscopy Market Worth 1.26 Billion USD by 2022

    Tuesday, August 16, 2016

    Infrared Nature in GMUNK Photography

    THE KHOOLL

    None of the images, work or art displayed here are our own, and we are really thankful to all of you who have created and represented personal and professional works. If there is something you do not wish to have here! please send us a message and we will gladly take it down!

    FOLLOW OUR OTHER BLOGS

    "The Khooll" is a digital design & life style magazine. Lifestyle magazine is an umbrella term for popular magazines concerned with lifestyle. There is no universally accepted definition of what constitutes a lifestyle magazine. It is often used to encompass a number of men's, women's magazines and magazines about design, health and fitness, tourism, leisure, fashion, decorating, or culture. The concept is chiefly used in reference to a magazine's tone. So here we go, this is our take on it… Enjoy Responsibly.

    archatlas:

    Infrared Nature in GMUNK Photography

    Well-known motion and digital creative director GMUNK has a hook on making awesome photographs with a strong selective vision. Beside shooting urban patterns he recently encountered into infrared photography delivering amazing shots of nature shot as seemed it is from another dimension.

    Text via

    (via archatlas)


    Source: Infrared Nature in GMUNK Photography

    Saturday, August 13, 2016

    Chasing Storms: Thunderhead Over The Cornfield

    Thunderhead Over The Corn Field

    Thunderhead Over The Corn Field

    I'm finding my focus in my Infrared Photography, I take the shot, convert it to black and white and I am drawn to the grainy quality of the photograph, I don't want to lose it,it has a timeless, emotional look to me. Today, I went out chasing a rumbling thunderstorm I could hear from miles away and I caught up with it breaking over a corn field.

    A beautiful thing to see, the sky was just alive, and to the left, I could see the rain breaking out of the sky.

    Someone wrote to me this morning complaining about the IR photographs, she just likes color photos of the farm and the animals, I ignored the message. The writer said she admired my creativity, but just wanted the color photographs. I thought of writing her back and saying creativity is all about exploration and experimentation and a wiliingness to make mistakes. If I'm not willing to do that, I can never learn or grow.

    Sometimes I think I'm like Donald Trump in that I sometimes feel I need to respond to messages like that, but I am not like Donald Trump, I don't revel in my mistakes, I love to learn from mine.

    I didn't reply.  I am very fond of this photography, and of the process of learning and evolving. I'm sorry people send messages like that, I have enough creative ego by now to keep moving forward, but people can easily be shut down by thoughtless comments. My message is to keep on,  eventually we get to a good place. I am getting close to mine.


    Source: Chasing Storms: Thunderhead Over The Cornfield

    Saturn Goes Psychedelic in Crazy, Colorful Infrared Photo

    This false-color view of Saturn's northern hemisphere shows details of the planet's cloudy atmosphere that are otherwise invisible to the human eye.

    A new photo of Saturn taken by NASA's Cassini spacecraft depicts the planet's northern hemisphere as a swirling mess of green, blue and purple clouds. What looks like a colossal oil slick on the otherwise yellow-tinted planet is actually a matter of wavelength.

    The funky-colored clouds in the Saturn photo are the result of the spectral filters on Cassini's camera. These filters can selectively reflect or transmit specific colors of light.

    Kevin Gill, an engineer at NASA's Jet Propulsion Laboratory in Pasadena, California and amateur space-imaging enthusiast, produced the false-color image by combining several photos captured by Cassini's wide-angle camera on July 20. [More Amazing Saturn Photos by Cassini]

    Gill used a combination of spectral filters that are sensitive to infrared light at wavelengths of 750, 727 and 619 nanometers. The human eye can typically see light only in the range of 390 to 700 nanometers, so using the spectral filters allows people to view what is otherwise invisible to the naked eye. This type of infrared filter allows researchers to study how Saturn's atmosphere reflects and absorbs specific wavelengths of sunlight.

    The Cassini spacecraft has been in orbit around Saturn since 2004 to study the planet and its moons, and is expected to do so until the mission ends, in September 2017.

    Email Hanneke Weitering at hweitering@space.com or follow her @hannekescience. Follow us @Spacedotcom, Facebook and Google+. Original article on Space.com.


    Source: Saturn Goes Psychedelic in Crazy, Colorful Infrared Photo

    Friday, August 12, 2016

    New IR camera could identify landing spots on the Moon (and Mars)

    A set of infrared cameras could just make another moon landing possible, and after that, maybe even Mars.

    This week, NASA signed a contract with Lockheed Martin allowing a 2018 Orion Exploration Mission to include a system of infrared cameras known as SkyFire. Those cameras are expected to obtain more detailed images of the moon's surface, scouting out potential areas for future human exploration. If the launch is successful, similar technology could be used to assess the possibility of sending astronauts to Mars.

    Related: Lockheed Martin joins the space race to Mars

    The agreement lets Lockheed Martin put SkyFire on NASA's Orion EM-1 launch, in exchange for data from the cameras. According to Lockheed Martin's SkyFire project manager, John Ringelberg, the lunar flyby will help fill in lunar knowledge gaps as well as explore the potential for using the technology for further space exploration.

    The SkyFire is a six-unit CubeSat, or a miniature satellite made up of several smaller units. CubeSats allow for smaller auxiliary projects to be completed alongside a larger mission.

    Cameras in space certainly aren't a new concept, but the technology under development by Lockheed Martin is lighter. Cutting out weight means the satellite could orbit closer to the moon than current technology allows, since a lighter load would make it easier to maneuver.

    "The CubeSat will look for specific lunar characteristics like solar illumination areas," James Russell, a Lockheed Martin SkyFire principal investigator, said in a press release. "We'll be able to see new things with sensors that are less costly to make and send to space."

    According to Lockheed Martin, the moon mission serves as a sort of trial run for the SkyFire system. If the cameras are successful shooting the moon, they could be used to photograph Mars. And the IR photos aren't your average space photos – the system could potentially reveal details like ideal landing sites and the safest areas for human exploration.

    "For a small CubeSat, SkyFire has a chance to make a big impact on future planetary space missions," Russell said. "With less mass and better instruments, we can get closer, explore deeper, and learn more about the far reaches of our solar system."

    SkyFire is one of 13 other CubeSats expected to hitch a ride on the EM-1 sometime in 2018.


    Source: New IR camera could identify landing spots on the Moon (and Mars)

    Thursday, August 11, 2016

    Turn Around and Go Back

    Posted on Aug 11, 2016 in Featured, Monochrome, Panasonic

    Today's Post by Mark Toal

    Have you ever been driving down the road and see something that you want to photograph but decide that it's too hard or time consuming to go back? Stopping at Thunder Mountain Monument in Imlay, Nevada almost 25 years ago convinced me to stop there every time that I can.

    IR Thunder Mountain cars

    I was driving east from Reno when I first noticed the strange buildings and sculptures. It was few miles to the next exit on Interstate 80 where I could turn around but I'll never regret it. Besides taking photos I saw a box asking for donations to restore the place. I put a check for $50 in the box and headed down the road. The son of the man who built Thunder Mountain called me to say thank you and invited me back to get the complete tour. I've been back about a dozen times over the years including about a month ago with my infrared converted Lumix GX7.

    IR TM head 2

    It is hard to photograph in the desert in the summer but luckily I remembered how Joe mentioned that infrared capture loves the midday sun. These would have been absolutely boring in color in the harsh desert light.

    Next time you see something interesting stop and go back. It might change your life.

    IR.book.cover

    Joe's book The Complete Guide to Digital Infrared Photography is currently out of print but you can get an affordable used copy or not-so-affordable new copies of the book from Amazon.com.


    Source: Turn Around and Go Back

    Wednesday, August 10, 2016

    Indochinese leopard has disappeared from 94% of its historical range

  • An estimated 973 to 2503 Indochinese leopards remain in the wild, a new study has found, of which only 409 to 1051 are breeding adults.
  • The Indochinese leopard is now extinct in Singapore, functionally extinct in Laos and Vietnam, and nearly extinct in Cambodia and China.
  • Researchers have identified three priority sites for Indochinese leopard conservation: Peninsular Malaysia, the Northern Tenasserim Forest Complex on Thailand-Myanmar border, and a small isolated population in eastern Cambodia.
  • The Indochinese leopard is struggling to survive.

    Once widespread across southeast Asia, the leopard subspecies has been wiped out from much of its habitat, and now occurs only in six percent of its historical range, a new study published in Biological Conservation has found.

    "Nobody was expecting this," co-author Jan F. Kamler, Southeast Asia Leopard Program Coordinator for Panthera, the global wild cat conservation organization, told Mongabay. "All had assumed that the leopard was still quite common throughout the forests of Southeast Asia. Conservationists had recognized that tigers had decreased dramatically throughout all of Southeast Asia, but they hadn't yet realized a similar range collapse occurred for the leopard as well."

    Leopard 1: Male Indochinese leopard from eastern Cambodia. Photo courtesy of Panthera, WWF Cambodia, and Forestry Administration.Male Indochinese leopard from eastern Cambodia. Photo courtesy of Panthera, WWF Cambodia, and Forestry Administration.

    After reviewing data from 146 wildlife surveys spanning across the last 20 years, an international team of researchers have found that an estimated 973 to 2503 Indochinese leopards remain in the wild. Only 409 to 1051 individuals are breeding adults.

    Country-wise data revealed that the Indochinese leopard is now extinct in Singapore and functionally extinct in Laos and Vietnam, with no viable populations remaining in the wild. The subspecies is also nearly extinct in Cambodia and China.

    The leopard now occupies only eight percent of its historical range in Cambodia, the study found, with just one remaining viable population in the Eastern Plains Landscape. Similarly, in China, the leopard now occurs only in 0.4 percent of its historical range. The leopard's habitat in Malaysia, Myanmar and Thailand has also shrunk dramatically, the study found.

    In fact, only two major strongholds remain for the Indochinese leopard, the scientists conclude — one in Peninsular Malaysia, and the other in the Northern Tenasserim Forest Complex on Thailand-Myanmar border — making them the top two priority sites for leopard conservation. The team has also identified eastern Cambodia as a third priority site, "because of its uniqueness and high conservation value."

    Given this dramatic decline of the Indochinese leopard, researchers recommend re-classifying this subspecies from Vulnerable to Endangered on the IUCN Red List. Doing this could help in imposing harsher penalties and improve protection of this subspecies, according to Kamler.

    "Whereas now the fine for killing a leopard might result in a small fine, if they become officially listed as Endangered by the IUCN, the penalties for killing them should increase to prison time and large fines — which hopefully will be a stronger deterrent against killing them," Kamler said. "Secondly, endangered species get more exposure and conservation money than other species. Consequently, NGOs can begin listing the Indochinese leopard as priority species in the region, thereby better promoting their conservation."

    Leopard 3: Melanistic male Indochinese leopard from Malaysia, with spots illuminated using infrared light. Photo courtesy of DWNP, Panthera, and Rimba. Melanistic male Indochinese leopard from Malaysia, with spots illuminated using infrared light. Photo courtesy of DWNP, Panthera, and Rimba.

    The team believes that the major threat to the Indochinese leopard is poaching for illegal wildlife trade. This is because leopards are increasingly being used as substitutes for tiger parts, Kamler said, with the price of leopard parts rising as tiger parts become scarce.

    "Across large parts of Southeast Asia, particularly in Laos, Cambodia, and Vietnam, there is an epidemic of snaring, and this appears to be the primarily factor driving leopards to extinction in those areas," Kamler added.

    A previous study found that overall, leopards have lost more than 75 percent of their historic habitat. The fate of the Indochinese leopard, too, depends on securing the protection of the last remaining populations. And this means that the three priority sites identified in the study need to be especially secured from additional poaching, Kamler said. This would include, for example, removal of a large number of snares that have already been set in these areas.

    The team hopes that the study will prompt governments and NGOs to take immediate action to prevent further loss of leopard habitat.

    "In response to this conservation crisis, Panthera just expanded their Leopard Program to include Southeast Asia, and already this year we're establishing long-term monitoring nodes in the last remaining Indochinese leopard populations in Southeast Asia, which includes sites in Cambodia, Malaysia, Thailand, and potentially Myanmar," Kamler said. "Besides establishing nodes to keep track of leopard numbers with camera traps, we're working with governments and local NGOs to improve enforcement at priority sites in southeast Asia."

    CITATION:

    Article published by Shreya Dasgupta on 2016-08-10.


    Source: Indochinese leopard has disappeared from 94% of its historical range

    Syracuse football starting LB Parris Bennett, CB Cordell Hudson full-go on Day 5 (photos/videos)

    Syracuse, N.Y. — Syracuse returned all five of its limited players, including multiple starters, to full-go at practice on Wednesday morning.

    Junior linebacker Parris Bennett, redshirt sophomore cornerback Cordell Hudson, redshirt senior tight end Josh Parris, senior linebacker Ted Taylor and redshirt junior safety Chauncey Scissum all ditched their green jerseys in favor of orange (offense) or white (defense) ones.

    Moving inside to the Ensley Athletic Center due to inclement weather, the Orange went through its regular routine during the 10 minutes media were allowed to watch.

    Quarterbacks threw routes vs. air to wide receivers and tight ends, running backs went through resistance and elevated rope ladder drills, offensive linemen worked on getting out of their stance, defensive players stretched and worked on learning various alignments and calls.

    SU freshman safety Devon Clarke continued to watch from the sidelines due to what head coach Dino Babers previously called a "medical issue."

    Here are some videos and observations from the brief session:

    Steve Ishmael shines

    Orange junior wideout Steve Ishmael continued to prove why he's the team's top option at outside receiver.

    Ishmael pulled in an out route off his shoes and was complimented by wide receivers coach Kim McCloud for his sharp route-running after another. Junior Jamal Custis and freshman Devin Butler have also been strong performers at the position early in camp.

    On the other side, redshirt senior tight end Cam MacPherson, redshirt junior inside receiver Sean Avant and sophomore outside receiver Kenterius Womack all dropped passes.

    Here's a minute of video from the RVA work. The quarterbacks on the near side are freshman Rex Culpepper (15), redshirt junior Austin Wilson (5) and freshman walk-on Mo Hasan.

    A look at the offensive line

    We haven't touched on the offensive line much in these posts. That's because the players mostly work on getting out of their stance.

    Here's a look at some of that drill work. It's also worth reminding that redshirt freshman Evan Adams is getting work at center after finishing the spring as the second-team right tackle.

    The return of the spring playlist

    Moving back inside Ensley meant the return of the spring playlist. As soon as the clock hit 6:45 a.m., an SU assistant plugged in an iPod and turned on the playlist.

    Of course, "Smooth" by Santana (featuring Rob Thomas) came on first followed by the noticeably clean version of "The Next Episode" by Dr. Dre. (featuring Snoop Dogg, Kurupt, and Nate Dogg).

    Sophomore walk-on inside receiver Jacob Hill was digging it.

    Healthier Syracuse football offensive line gives hurry-up spread 'a chance,' coach says:

    Contact Stephen Bailey anytime: Email | Twitter


    Source: Syracuse football starting LB Parris Bennett, CB Cordell Hudson full-go on Day 5 (photos/videos)